1 x Brand New Remote (Either a Boss or Steel-Line Genuine Remote – Model- 303RTX)
Keyring Attachment
1 x Battery
Coding Instructions
Additional items included for Boss HT4 2211L – 2 Button Remote
Wall caddie
Sun-visor clip
DO NOT PURCHASE THIS REMOTE IF YOU HAVE A ROLLER DOOR OPENER (SEE NOTES BELOW in COMPATIBILITY)
Compatibility List:
BOSS HT4 2211L – TILT, OVERHEAD AND PANEL Garage Door
BOSS HT3 BLUE LED v 1
BOSS HT3 BLUE LED v2
GUARDIAN 2211L
GUARDIAN HT3 BLUE LED
STEEL-LINE 2211L 1,2 and 4 Button – TILT, OVERHEAD AND PANEL Garage Door
STEEL-LINE HT3 BLUE
IMPORTANT NOTE: The newest model upgrade of the BOSS and STEEL-LINE HT4 2211L remote does not have the ability to code into the original Steel-Line and Boss ROLLERDOORS. If you require a ROLLERDOOR remote you will need to purchase a Generic Remote.
Remove the face plate by inserting a screwdriver into the slot located on the bottom side of the face plate.
The “Radio Set” button is located under the large AQUA Open/Close button.
With the power turned on to the unit, press and release the small button.
The yellow LED will come on indicating that your unit is ready to accept a code.
How to access the receiver in overhead opener
To the left of the four adjustment buttons is a recessed button marked “Radio Set”, with a pointed object momentarily push this button.
lf the courtesy light is off it will come on and stay on for 30 seconds.
If the courtesy light is on it will flash once and then stay on for 30 seconds indicating that your unit is ready to accept a code.
How to program the Boss HT4 2211L Remote to the Opener
Press the handset button you want to operate this device once.
If the code is accepted the green LED or courtesy light will blink twice.
If you are programming multiple handsets code them in at this stage.
Overhead Panel Lift/Tilt Operator – Unit resets automatically
Roller Door Operator – After CODING press and release the small button (learning button) and the yellow LED will show reset complete. Handset is now programmed and ready to use.
How to Delete all transmitters from memory
ROLLER DOOR OPERATOR – turn power off then press & HOLD down the “Radio Set” button while you turn the power on. The 3 LED’s will flash twice indicating that all codes have been deleted. OVERHEAD PANEL LIFT/TILT OPERATOR – memory hold the radio set button in for 5 seconds The courtesy light will then flash 7 times indicating all transmitters have been cleared from the memory. DUAL ACCESS – WHITE BUTTON CENTRES – This is coded by the internal dip switches & an existing working remote should be used as a reference to set the sequence. PRIVATE ENTRY / RED BUTTON – Code other buttons as above.
Instructional Video – Setting up the OL4 Sectional garage door operator
Reviews
There are no reviews yet.
Only logged in customers who have purchased this product may leave a review.
Features:
Genuine Original Equipment Remote
Free Shipping Australia-Wide*
2 Years Manufacturers Warranty*
Includes:
1 x Brand New Remote (Either a Boss or Steel-Line Genuine Remote – Model- 303RTX)
Keyring Attachment
1 x Battery
Coding Instructions
Additional items included for Boss HT4 2211L – 2 Button Remote
Wall caddie
Sun-visor clip
DO NOT PURCHASE THIS REMOTE IF YOU HAVE A ROLLER DOOR OPENER (SEE NOTES BELOW in COMPATIBILITY)
Compatibility List:
BOSS HT4 2211L – TILT, OVERHEAD AND PANEL Garage Door
BOSS HT3 BLUE LED v 1
BOSS HT3 BLUE LED v2
GUARDIAN 2211L
GUARDIAN HT3 BLUE LED
STEEL-LINE 2211L 1,2 and 4 Button – TILT, OVERHEAD AND PANEL Garage Door
STEEL-LINE HT3 BLUE
IMPORTANT NOTE: The newest model upgrade of the BOSS and STEEL-LINE HT4 2211L remote does not have the ability to code into the original Steel-Line and Boss ROLLERDOORS. If you require a ROLLERDOOR remote you will need to purchase a Generic Remote.
Remove the face plate by inserting a screwdriver into the slot located on the bottom side of the face plate.
The “Radio Set” button is located under the large AQUA Open/Close button.
With the power turned on to the unit, press and release the small button.
The yellow LED will come on indicating that your unit is ready to accept a code.
How to access the receiver in overhead opener
To the left of the four adjustment buttons is a recessed button marked “Radio Set”, with a pointed object momentarily push this button.
lf the courtesy light is off it will come on and stay on for 30 seconds.
If the courtesy light is on it will flash once and then stay on for 30 seconds indicating that your unit is ready to accept a code.
How to program the Boss HT4 2211L Remote to the Opener
Press the handset button you want to operate this device once.
If the code is accepted the green LED or courtesy light will blink twice.
If you are programming multiple handsets code them in at this stage.
Overhead Panel Lift/Tilt Operator – Unit resets automatically
Roller Door Operator – After CODING press and release the small button (learning button) and the yellow LED will show reset complete. Handset is now programmed and ready to use.
How to Delete all transmitters from memory
ROLLER DOOR OPERATOR – turn power off then press & HOLD down the “Radio Set” button while you turn the power on. The 3 LED’s will flash twice indicating that all codes have been deleted. OVERHEAD PANEL LIFT/TILT OPERATOR – memory hold the radio set button in for 5 seconds The courtesy light will then flash 7 times indicating all transmitters have been cleared from the memory. DUAL ACCESS – WHITE BUTTON CENTRES – This is coded by the internal dip switches & an existing working remote should be used as a reference to set the sequence. PRIVATE ENTRY / RED BUTTON – Code other buttons as above.
Instructional Video – Setting up the OL4 Sectional garage door operator
Reviews
There are no reviews yet.
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.