Elsema FOBKIT FOB43302 with 2 Ch Wire In Receiver

Brand: Elsema

Elsema Logo

Elsema FOBKIT FOB43302 with 2 Ch Wire In Receiver

Brand: Elsema

Elsema Logo

Each FobKit  comes with:

  • 1 x 2ch Wire in Receiver PCR43302R
  • 3 x Genuine Brand New Orange FOB43302 remotes
  • 3 x Battery
  • 3 x Keyring Attachment
  • Coding Instructions
  • Free Shipping Australia-Wide*
  • 2 Years Manufacturers Warranty*

Features:

  • Versatile remote available in a 1,2,4 or 5 button variety (this listing is for the 2 button)
  • Simultaneously transmits the encrypted code on 5 different frequencies, making it impossible for the remote to be interfered with or jammed
  • Uses frequency hopping spread spectrum (FHSS)
  • Operating range of up to 100 metres depending on building structure and receiver antenna
  • Wide operating supply voltage and low current consumption ▪ Momentary and latching modes are user selectable. ▪ On-board diagnostic LED’s to indicate correct power, reception and relay activation
  • Although the FOB43301 is available in 4 colours the general colour supplied in FOBKITS is Orange.  The colour will vary depending on stock levels at the time of purchase. 
  • Designed in Australia
  • Free Delivery Australia-Wide*
  • 2 Years Manufacturers Warranty*

Each FobKit  comes with:

  • 1 x 2 Ch Wire In Receiver PCR43302R
  • 3 x Genuine Brand New Orange FOB43302 remotes
  • 3 x Battery
  • 3 x Keyring Attachment
  • Coding Instructions

There are multiple variations of this product

 


WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Never allow children to replace button batteries on any device. Swallowing or placing inside any part of the body may lead to severe or fatal injuries in as little as 2 hours or less due to chemical burns and potential perforation of the oesophagus.

If you suspect your child has swallowed a button battery or placed inside any part of the body immediately call the POISONS INFORMATION CENTRE on 13 11 26 for prompt advice. If your child is having any difficulty breathing, contact 000.

Dispose of used button/coin batteries immediately and safely. A battery can still be dangerous even when it can no longer operate the device. Place sticky tape around both sides of the battery and dispose of it immediately out of reach of children in an outside bin or recycle safely.

Please see button battery safety information from the Australian Competition & Consumer Commission (ACCC).

Weight.20 kg
Brand

Elsema

MPN

Does Not Apply

UPC

Does not apply

Type

,

Frequency5 x Secure Frequencies – 433.10 to 434.70MHz
Coding TypeRolling Code
Receiver TypeWired In Receiver
Channels1
Receiver Range>100-200m
Receiver Supply11-28v AC/DC
Receiver Sensitivity< 0.316µV
Receiver Dimensions70 x 55 x 25mm
Remote Buttons5
Button ColourWhite
Case ColourDefault is Orange (Other Colours will be supplied only when Orange is not available)
Remote Size60x38x10mm
Remote Range> 100 meters

How to Program the Elsema PentaFOB® remotes

Remote to Receiver

1. Check that all switches are “OFF” on the receivers 12-way dip switch
2. Press and hold the program button on the receiver
3. Press the remote button for 2 seconds, receiver LED will flash and then turn Green
4. Release the button on the receiver and the remote
5. Press remote control button to test the receiver output

Remote to Remote (you will need to be near the receiver for this procedure)

If your receiver was manufactured prior to 2016

1. Open the case of a remote control that is already programmed and press and release the program button on the back of the board (The receiver enters learning mode)
2. Press the button of the remote in step 1 which activates the receiver
3. Press the button on the new remote which needs to be programmed for 2 seconds
4. Press the program button again of the remote in step 1(The receiver exits learning mode)
5. Press the new remote control button to test the receiver output

If your receiver was manufactured 2016 onwards

1. Open the case of a remote control that is already programmed and press and release the program button on the back of the board
2. Press the new remote control button for 2 seconds
3. Press the new remote control button again to test the receiver output

Video Programming

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Features:

  • Versatile remote available in a 1,2,4 or 5 button variety (this listing is for the 2 button)
  • Simultaneously transmits the encrypted code on 5 different frequencies, making it impossible for the remote to be interfered with or jammed
  • Uses frequency hopping spread spectrum (FHSS)
  • Operating range of up to 100 metres depending on building structure and receiver antenna
  • Wide operating supply voltage and low current consumption ▪ Momentary and latching modes are user selectable. ▪ On-board diagnostic LED’s to indicate correct power, reception and relay activation
  • Although the FOB43301 is available in 4 colours the general colour supplied in FOBKITS is Orange.  The colour will vary depending on stock levels at the time of purchase. 
  • Designed in Australia
  • Free Delivery Australia-Wide*
  • 2 Years Manufacturers Warranty*

Each FobKit  comes with:

  • 1 x 2 Ch Wire In Receiver PCR43302R
  • 3 x Genuine Brand New Orange FOB43302 remotes
  • 3 x Battery
  • 3 x Keyring Attachment
  • Coding Instructions

There are multiple variations of this product

 


WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Never allow children to replace button batteries on any device. Swallowing or placing inside any part of the body may lead to severe or fatal injuries in as little as 2 hours or less due to chemical burns and potential perforation of the oesophagus.

If you suspect your child has swallowed a button battery or placed inside any part of the body immediately call the POISONS INFORMATION CENTRE on 13 11 26 for prompt advice. If your child is having any difficulty breathing, contact 000.

Dispose of used button/coin batteries immediately and safely. A battery can still be dangerous even when it can no longer operate the device. Place sticky tape around both sides of the battery and dispose of it immediately out of reach of children in an outside bin or recycle safely.

Please see button battery safety information from the Australian Competition & Consumer Commission (ACCC).

Weight.20 kg
Brand

Elsema

MPN

Does Not Apply

UPC

Does not apply

Type

,

Frequency5 x Secure Frequencies – 433.10 to 434.70MHz
Coding TypeRolling Code
Receiver TypeWired In Receiver
Channels1
Receiver Range>100-200m
Receiver Supply11-28v AC/DC
Receiver Sensitivity< 0.316µV
Receiver Dimensions70 x 55 x 25mm
Remote Buttons5
Button ColourWhite
Case ColourDefault is Orange (Other Colours will be supplied only when Orange is not available)
Remote Size60x38x10mm
Remote Range> 100 meters

How to Program the Elsema PentaFOB® remotes

Remote to Receiver

1. Check that all switches are “OFF” on the receivers 12-way dip switch
2. Press and hold the program button on the receiver
3. Press the remote button for 2 seconds, receiver LED will flash and then turn Green
4. Release the button on the receiver and the remote
5. Press remote control button to test the receiver output

Remote to Remote (you will need to be near the receiver for this procedure)

If your receiver was manufactured prior to 2016

1. Open the case of a remote control that is already programmed and press and release the program button on the back of the board (The receiver enters learning mode)
2. Press the button of the remote in step 1 which activates the receiver
3. Press the button on the new remote which needs to be programmed for 2 seconds
4. Press the program button again of the remote in step 1(The receiver exits learning mode)
5. Press the new remote control button to test the receiver output

If your receiver was manufactured 2016 onwards

1. Open the case of a remote control that is already programmed and press and release the program button on the back of the board
2. Press the new remote control button for 2 seconds
3. Press the new remote control button again to test the receiver output

Video Programming

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.