WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Never allow children to replace button batteries on any device. Swallowing or placing inside any part of the body may lead to severe or fatal injuries in as little as 2 hours or less due to chemical burns and potential perforation of the oesophagus.
If you suspect your child has swallowed a button battery or placed inside any part of the body immediately call the POISONS INFORMATION CENTRE on 13 11 26 for prompt advice. If your child is having any difficulty breathing, contact 000.
Dispose of used button/coin batteries immediately and safely. A battery can still be dangerous even when it can no longer operate the device. Place sticky tape around both sides of the battery and dispose of it immediately out of reach of children in an outside bin or recycle safely.
Warning: This Product contains a button or coin cell battery.
Hazardous if Swallowed
PROGRAMMING TO THE PLUG IN (RX4X Receiver)
This receiver is found in the SUN5024FAU, SUN11024 via a plug in receiver.
Press and release the receiver button once to place the receiver into Learning Mode.
LED on the receiver will flash number of times equal to the number of outputs selected (1 second pause between each flash)
On your NEW remote, push and hold the button you wish to control the opener for more than 2 seconds.
The receiver LED will give one long flash to confirm successfully coded.
Continue with Step 3 for each button or remote you wish to program.
DELETING A REMOTE FROM THE PLUG IN (RX4X Receiver)
Press Receiver button (approximately 3 seconds) until radio LED lights UP
Within 7 seconds press and hold the key on the remote to be deleted until the Receiver LED goes OUT. Release the remote button.
The Receiver LED starts to flash (About 1 second after the Remote button is released)
Press Receiver button to confirm deletion
Receiver LED will give one long flash if successfully deleted.
PROGRAMMING TO THE CT10224 CONTROL BOARD
Press and Release the DOWN (RADIO) button to the position output you are wishing to program (Normal is ONCE for Step by Step. Other Outputs can be found within the Control Boards Manual
KEY LED will flash a number of times equal to the number of the output selected with 1 second pauses between flashes
Press the Key of the remote to be programmed for at least 2 seconds
LED will give one long flash if successful.
To Program additional remotes or buttons, repeat point 3
Note: If no Commands are given within 7 seconds the receiver will automatically disengage from the programming mode
PROGRAMMING FOR FORZA 1200 or BOSS HT20
Press the “S” button on the opener until “0” appears on the screen, then release the button.
Press the desired button on your remote that you wish to use.
The “0” on the screen will disappear and your remote has been coded.
Reviews
There are no reviews yet.
Only logged in customers who have purchased this product may leave a review.
WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Never allow children to replace button batteries on any device. Swallowing or placing inside any part of the body may lead to severe or fatal injuries in as little as 2 hours or less due to chemical burns and potential perforation of the oesophagus.
If you suspect your child has swallowed a button battery or placed inside any part of the body immediately call the POISONS INFORMATION CENTRE on 13 11 26 for prompt advice. If your child is having any difficulty breathing, contact 000.
Dispose of used button/coin batteries immediately and safely. A battery can still be dangerous even when it can no longer operate the device. Place sticky tape around both sides of the battery and dispose of it immediately out of reach of children in an outside bin or recycle safely.
Warning: This Product contains a button or coin cell battery.
Hazardous if Swallowed
PROGRAMMING TO THE PLUG IN (RX4X Receiver)
This receiver is found in the SUN5024FAU, SUN11024 via a plug in receiver.
Press and release the receiver button once to place the receiver into Learning Mode.
LED on the receiver will flash number of times equal to the number of outputs selected (1 second pause between each flash)
On your NEW remote, push and hold the button you wish to control the opener for more than 2 seconds.
The receiver LED will give one long flash to confirm successfully coded.
Continue with Step 3 for each button or remote you wish to program.
DELETING A REMOTE FROM THE PLUG IN (RX4X Receiver)
Press Receiver button (approximately 3 seconds) until radio LED lights UP
Within 7 seconds press and hold the key on the remote to be deleted until the Receiver LED goes OUT. Release the remote button.
The Receiver LED starts to flash (About 1 second after the Remote button is released)
Press Receiver button to confirm deletion
Receiver LED will give one long flash if successfully deleted.
PROGRAMMING TO THE CT10224 CONTROL BOARD
Press and Release the DOWN (RADIO) button to the position output you are wishing to program (Normal is ONCE for Step by Step. Other Outputs can be found within the Control Boards Manual
KEY LED will flash a number of times equal to the number of the output selected with 1 second pauses between flashes
Press the Key of the remote to be programmed for at least 2 seconds
LED will give one long flash if successful.
To Program additional remotes or buttons, repeat point 3
Note: If no Commands are given within 7 seconds the receiver will automatically disengage from the programming mode
PROGRAMMING FOR FORZA 1200 or BOSS HT20
Press the “S” button on the opener until “0” appears on the screen, then release the button.
Press the desired button on your remote that you wish to use.
The “0” on the screen will disappear and your remote has been coded.
Reviews
There are no reviews yet.
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.