LEXO - PTX5 & PTX6 Aftermarket Remote

Brand: LEXO

LEXO – PTX5 & PTX6 Aftermarket Remote

Brand: LEXO

Includes:

  • 1 x After Market Remote
  • 1 x Battery
  • Coding Instructions
  • Key Ring Attachment
  • Free Shipping Australia-Wide*
  • 2 years manufacturers Warranty*

Note:  This listing is for an Aftermarket Compatible Remote.     

$24.95

Availability:

In stock

Availability:

In stock

Includes:

  • 1 x After Market Remote
  • 1 x Battery
  • Coding Instructions
  • Key Ring Attachment
  • Free Shipping Australia-Wide*
  • 2 years manufacturers Warranty*
Note:  This listing is for an Aftermarket Compatible Remote.     

Features:

  • 1 x After Market Compatible Remote
  • 2 Years Manufacturers Warranty*
  • Free Standard Shipping Australia-Wide*

Includes:

  • 1 x After Market Remote
  • 1 x Battery
  • Coding Instructions

Compatibility List:

This remote is compatible with the ATA TrioCode Series of Remotes:

Weight.030 kg
Brand

LEXO

Compatible Brand

ATA

MPN

Does Not Apply

UPC

Does not apply

Classification

TrioCode

Type

Number of Buttons

Remote Colour

Black, Chrome

AS62368.1 Battery Compliant

Not Applicable

Battery Technology

Lead-Acid

Features

Keyring, Wireless

Items Included

Battery, Installation Instructions, Remote

Power Source

Battery Powered

Warranty

2 Years*

Frequency433.47, 433.92 & 434.37 MHz
Code TypeRolling Code
Body TypeKey Ring
Number of Buttons4
Button ColourBlack
Case ColourBlack and Chrome
Remote Size50x 30x 12mm
Range< 40 meters

 

Item Contains Lithium Coin/Button BatteryNo
Battery Type27A
Access TypeTool Required
AS62368.1 CompliantN/A

Written Instructions

GDO, ELITE and NEOSLIDER’s

CODING USING A WORKING REMOTE

  • Take any genuine coded remote already programmed to the opener.  Press the button for the function you require until the door / gate is activated and release.
  • Then using a small needle or paper clip press on the Coding Bump in the middle of the remote firmly for two seconds – LED  lights.
  • Within 10 seconds pick up the new remote you wish to code.
  • Press the remote button you would like to use to open / close the device for two seconds.
  • Pause for two seconds then press the same button again for two seconds – button should now be coded.
  • Wait for 10 seconds, then press the just coded remoter button to confirm that it operates the device.

CODING DIRECT TO A RECEIVER

    • Press and hold the blue “Door Code” button on the opener or SW1 MAIN or SW2 PED on the receiver board.
    • Press the remote button you would like to open / close the device for two seconds.
    • Release and pause for two seconds. Press the same button again for two seconds.
    • Release the Door Code or SW button.Press the transmitter button to test operation of the door or gate etc.

DELETING ANY REMOTE ALREADY CODED

Coding a button again will delete it from memory.

DELETING ALL STORED TRANSMITTER CODES

      • Turn the power off to the opener.
      • Press and hold Door Code or SW1 button.
      • Turn the power on again, while holding the button. The coding LED will illuminate to indicate that the receiver’s memory has been deleted.
      • Release the button. All the stored codes including the courtesy light codes should now be all deleted.

ATS 2 & 3

CODING REMOTE TO REMOTE

  • Take any coded remote. Press the button for the function you require until the door / gate is activated and release.
  • Then using a small needle or paper clip press on the Coding Bump in the middle of the remote firmly for two seconds – LED lights.
  • Within 10 seconds pick up the new remote you wish to code.
  • Press the remote button you would like to use to open / close the device for two seconds.
  • Pause for two seconds then press the same button again for two seconds – button should now be coded.

Wait for 10 seconds, then press the just coded remoter button to confirm that it operates the device.

CODING DIRECT TO A RECEIVER

  • Remove the controls cover to access the buttons.
  • Press the MODE (6) button repetitively until the REMOTE INDICATOR (9) is lit.
  • Press and HOLD the CLOSE (1) button to set OPEN/ STOP/ CLOSE function. The Main light will start to flash rapidly.
  • Press on of the four buttons on your transmitter until the main light starts to flash rapidly.

Release both buttons.  Press the MODE (6) button to exit and refit controls cover.

DELETING ALL STORED TRANSMITTER CODES

  • Press the MODE (6) button repetitively until the REMOTE INDICTATOR (9) is lit.
  • Press and hold the MODE (6) button for 10 secs, let the MODE (6) button go when the main light stops flashing.

Video Instructions

Features:

  • 1 x After Market Compatible Remote
  • 2 Years Manufacturers Warranty*
  • Free Standard Shipping Australia-Wide*

Includes:

  • 1 x After Market Remote
  • 1 x Battery
  • Coding Instructions

Compatibility List:

This remote is compatible with the ATA TrioCode Series of Remotes:

Weight.030 kg
Brand

LEXO

Compatible Brand

ATA

MPN

Does Not Apply

UPC

Does not apply

Classification

TrioCode

Type

Number of Buttons

Remote Colour

Black, Chrome

AS62368.1 Battery Compliant

Not Applicable

Battery Technology

Lead-Acid

Features

Keyring, Wireless

Items Included

Battery, Installation Instructions, Remote

Power Source

Battery Powered

Warranty

2 Years*

Frequency433.47, 433.92 & 434.37 MHz
Code TypeRolling Code
Body TypeKey Ring
Number of Buttons4
Button ColourBlack
Case ColourBlack and Chrome
Remote Size50x 30x 12mm
Range< 40 meters

 

Item Contains Lithium Coin/Button BatteryNo
Battery Type27A
Access TypeTool Required
AS62368.1 CompliantN/A

Written Instructions

GDO, ELITE and NEOSLIDER’s

CODING USING A WORKING REMOTE

  • Take any genuine coded remote already programmed to the opener.  Press the button for the function you require until the door / gate is activated and release.
  • Then using a small needle or paper clip press on the Coding Bump in the middle of the remote firmly for two seconds – LED  lights.
  • Within 10 seconds pick up the new remote you wish to code.
  • Press the remote button you would like to use to open / close the device for two seconds.
  • Pause for two seconds then press the same button again for two seconds – button should now be coded.
  • Wait for 10 seconds, then press the just coded remoter button to confirm that it operates the device.

CODING DIRECT TO A RECEIVER

    • Press and hold the blue “Door Code” button on the opener or SW1 MAIN or SW2 PED on the receiver board.
    • Press the remote button you would like to open / close the device for two seconds.
    • Release and pause for two seconds. Press the same button again for two seconds.
    • Release the Door Code or SW button.Press the transmitter button to test operation of the door or gate etc.

DELETING ANY REMOTE ALREADY CODED

Coding a button again will delete it from memory.

DELETING ALL STORED TRANSMITTER CODES

      • Turn the power off to the opener.
      • Press and hold Door Code or SW1 button.
      • Turn the power on again, while holding the button. The coding LED will illuminate to indicate that the receiver’s memory has been deleted.
      • Release the button. All the stored codes including the courtesy light codes should now be all deleted.

ATS 2 & 3

CODING REMOTE TO REMOTE

  • Take any coded remote. Press the button for the function you require until the door / gate is activated and release.
  • Then using a small needle or paper clip press on the Coding Bump in the middle of the remote firmly for two seconds – LED lights.
  • Within 10 seconds pick up the new remote you wish to code.
  • Press the remote button you would like to use to open / close the device for two seconds.
  • Pause for two seconds then press the same button again for two seconds – button should now be coded.

Wait for 10 seconds, then press the just coded remoter button to confirm that it operates the device.

CODING DIRECT TO A RECEIVER

  • Remove the controls cover to access the buttons.
  • Press the MODE (6) button repetitively until the REMOTE INDICATOR (9) is lit.
  • Press and HOLD the CLOSE (1) button to set OPEN/ STOP/ CLOSE function. The Main light will start to flash rapidly.
  • Press on of the four buttons on your transmitter until the main light starts to flash rapidly.

Release both buttons.  Press the MODE (6) button to exit and refit controls cover.

DELETING ALL STORED TRANSMITTER CODES

  • Press the MODE (6) button repetitively until the REMOTE INDICTATOR (9) is lit.
  • Press and hold the MODE (6) button for 10 secs, let the MODE (6) button go when the main light stops flashing.

Video Instructions